|
It is currently Mon Nov 25, 2024 10:50 pm |
|
All times are UTC - 7 hours [ DST ] |
|
Page 1 of 1 |
[ 5 posts ] |
| Previous topic | Next topic |
EFI fuel lines & fittings
| Author | Message |
|---|---|
|
Official CCB Member   Joined: Mon Jan 03, 2011 6:07 pm Posts: 4074 Location: Gardnerville, NV 
|
 EFI fuel lines & fittingsIs it considered acceptable that I'm using rubber EFI fuel hose & clamps on an E2000 pump built for the Ford factory nylon snap lock hoses? I ran it for years that way, no problems, no leaks. But if there is a likelyhood the hose could pull off the pump, I'd probably change it out for one made for rubber hose. I just bumped into this one while reading up on Explorer EFI.
https://www.amazon.com/dp/B001BFOBXA/re ... 4f8fc2ef_S I'm happy leaving it as is, if I'm not flirting with disaster. I haven't read anything about mixing line/fitting types. And I know the E2000 pump has been used a lot, probably without the Ford fuel line. So I'm guessing I'm fine, and I'm just overthinking it. _________________ "America is at that awkward stage. It's too late to work within the system, but too early to shoot the bastards." – Claire Wolfe 74-AWB 98", ZF5, Atlas4, TGW HP1060 and HP1014 axles, ARBs, 37's, 3.5" lift-5.5" front coil springs, Tahoe rear springs, EFI 302, h-boost, York OBA, 4x4x2, custom dash & gauges 72 U15- Explorer Sport-Candyapple Red (1 of 141) |
| Sat Aug 20, 2016 2:45 pm |
|
|
|
|
Official CCB Member  Joined: Tue May 07, 2013 10:37 pm Posts: 1485
|
Re: EFI fuel lines & fittings If you've run it for years it's probably ok at those pressures. If you plan to increase pressure with an explorer returnless system you might want to upgrade it. I use the same pump on my '74 and I put a couple AN tube adapters on the fittings.
|
| Sun Aug 21, 2016 12:37 am |
|
|
|
|
Official CCB Member Joined: Mon Jan 03, 2011 6:07 pm Posts: 4074 Location: Gardnerville, NV
|
Re: EFI fuel lines & fittings Thanks, I'm only going to worry about the high pressure side of the pump. The 5/16 snap lock fitting doesn't want to thread out of the pump (and I don't want to break the pump). Did you use something like this?:
https://www.amazon.com/Russell-640863-Q ... ZTJSW6GHP8 _________________ "America is at that awkward stage. It's too late to work within the system, but too early to shoot the bastards." – Claire Wolfe 74-AWB 98", ZF5, Atlas4, TGW HP1060 and HP1014 axles, ARBs, 37's, 3.5" lift-5.5" front coil springs, Tahoe rear springs, EFI 302, h-boost, York OBA, 4x4x2, custom dash & gauges 72 U15- Explorer Sport-Candyapple Red (1 of 141) |
| Sun Aug 21, 2016 11:05 am |
|
|
|
|
Official CCB Member Joined: Tue May 07, 2013 10:37 pm Posts: 1485
|
Re: EFI fuel lines & fittings I used tube adapters like this. https://www.summitracing.com/nv/parts/ear-165056erl
The one you found would be better. Tube adapters can only be installed once because they usually can't be removed. |
| Sun Aug 21, 2016 1:40 pm |
|
|
|
|
Official CCB Member Joined: Mon Jan 03, 2011 6:07 pm Posts: 4074 Location: Gardnerville, NV
|
Re: EFI fuel lines & fittings Thanks!
_________________ "America is at that awkward stage. It's too late to work within the system, but too early to shoot the bastards." – Claire Wolfe 74-AWB 98", ZF5, Atlas4, TGW HP1060 and HP1014 axles, ARBs, 37's, 3.5" lift-5.5" front coil springs, Tahoe rear springs, EFI 302, h-boost, York OBA, 4x4x2, custom dash & gauges 72 U15- Explorer Sport-Candyapple Red (1 of 141) |
| Sun Aug 21, 2016 4:16 pm |
|
|
|
|
|
Page 1 of 1 |
[ 5 posts ] |
|
All times are UTC - 7 hours [ DST ] |
Who is online |
Users browsing this forum: No registered users and 82 guests |
| You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum |