|
|
Register •
FAQ
• Login
|
|
|
It is currently Mon Nov 25, 2024 4:44 pm
|
|
Page 1 of 1
|
[ 6 posts ] |
|
| Author |
Message |
|
trei75bronco
Official CCB Member
Joined: Wed Jan 26, 2011 10:55 pm
Posts: 837
Images: 0
|
 Dana 20 seals Looking for a Dana 30 front output seal for the yoke and the bearing retainer and input seals.
Trei
7209360791
|
| Mon Apr 06, 2015 9:03 am |
|
|
|
ZOSO
Moderator
Joined: Mon Nov 15, 2010 5:58 pm
Posts: 3906
Location: Henderson, Co
|
Re: Dana 20 seals I've checked all the parts places and you cant get em. Only place would be BH or other venders.
_________________
Rob
74 Ranger EFI351w, 4r70w, ARB 5.13 9in, ARB 5.13D44, and a bunch of other goodies. Best of all the family memories.
04 Mustang Cobra, KenneBell 2.2 feeding a lot of boost on E85. Tire shredding machine
New project: 77 Bronco Ranger, body work and more body work.
Very little left of a 72 durango tan explorer sport
|
| Mon Apr 06, 2015 5:33 pm |
|
|
|
Viperwolf1
Official CCB Member
Joined: Tue May 07, 2013 10:37 pm
Posts: 1485
|
Re: Dana 20 seals Seals:
Input shaft seal (double lip)-CR #517383,Napa #NOS 18676, CR #18676 (good seal) (Do not use Timken #473179)
Output shaft seals-Timken #450185
Shift rail seals-CR #6204, Timken #471466
Yoke o-ring-1-1/4"OD x 1-1/8"ID x 1/16". Danco happened to be the brand at the hardware store and it is their #29.
Speedi-sleeve for yokes-SKF99155
Bearings:
Input- SKF #307NRJ
Rear output-Timken #25877 (inner), Timken #15117 (outer)
Front output, J shift-Timken #14116
Front output, T shift-Timken #14131
Cups:
Rear output-Timken #25821 (inner), Timken #15245 (outer)
Front output-Timken #14276 (both T and J)
Shims: 1.20" ID, 1.50" OD
Yoke nuts: 3/4", 16 tpi, top lock
When setting the rear output endplay use a Timken #15118 in the rear position. It is the same size as the #15117 except the inner bore is a couple thousandths larger. This allows you to assemble and disassemble the output shaft without needing a press. Only use it as a setup bearing. Once the correct endplay is set, drop in the #15117 bearing, put the seal on and assemble the shaft.
|
| Mon Apr 06, 2015 8:51 pm |
|
|
|
trei75bronco
Official CCB Member
Joined: Wed Jan 26, 2011 10:55 pm
Posts: 837
Images: 0
|
Re: Dana 20 seals Phil there was a small leak at the front output and I was getting a leak between the tcase and tranny. What would I need and are they at Napa?
|
| Wed Apr 08, 2015 7:03 pm |
|
|
|
Viperwolf1
Official CCB Member
Joined: Tue May 07, 2013 10:37 pm
Posts: 1485
|
Re: Dana 20 seals
|
| Wed Apr 08, 2015 11:00 pm |
|
|
|
trei75bronco
Official CCB Member
Joined: Wed Jan 26, 2011 10:55 pm
Posts: 837
Images: 0
|
Re: Dana 20 seals I never put a rubber washer on when the front yoke got bent. Guess I will start there i
|
| Fri Apr 10, 2015 5:27 am |
|
|
|
|
|
Page 1 of 1
|
[ 6 posts ] |
|
Who is online |
Users browsing this forum: No registered users and 77 guests |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum
|
|
