|
|
Register •
FAQ
• Login
|
|
|
It is currently Mon Nov 25, 2024 5:21 pm
|
|
Page 1 of 1
|
[ 8 posts ] |
|
| Author |
Message |
|
Backcountryrenegade
Official CCB Member
Joined: Fri May 15, 2015 10:28 pm
Posts: 41
Location: Elizabeth, CO
|
 351 install I’m blanking but don’t some of you guys live in franktown ish? I’m trying to install my 351 alone and could use some extra hands if anybody is around. Thanks!
|
| Sat Jul 14, 2018 3:45 pm |
|
|
|
Backcountryrenegade
Official CCB Member
Joined: Fri May 15, 2015 10:28 pm
Posts: 41
Location: Elizabeth, CO
|
Re: 351 install Update- got it about 90% in. Can’t seem to get it the last half a inch back. It the torque converter that I can tell. Any ideas?
Also- if anybody knows the size of the bolts for the bell housing and which hole they go in I’d appreciate it! Smart guy here can’t remember which bolts go in which holes!
|
| Sat Jul 14, 2018 6:40 pm |
|
|
|
Rox Crusher
Official CCB Member
Joined: Sun Oct 10, 2010 5:36 pm
Posts: 3980
Location: Roxborough Park, Colorado
|
Re: 351 install When you put the torque converter in you should have felt / heard 3 pronounced spots before it seats.
_________________
1977 Sport, 351w OBDII EFI motor, 4R70W auto, 4:88 gears, ARB lockers, 3.5" suspension, 33" tires.
|
| Sat Jul 14, 2018 6:49 pm |
|
|
|
Backcountryrenegade
Official CCB Member
Joined: Fri May 15, 2015 10:28 pm
Posts: 41
Location: Elizabeth, CO
|
Re: 351 install Did. It went all the way in. Just can’t get the motor back.
|
| Sun Jul 15, 2018 1:39 pm |
|
|
|
horseplay
Official CCB Member
Joined: Mon Jan 21, 2013 8:24 pm
Posts: 408
Location: Grand Junction CO
|
Re: 351 install you might want to check the end of the crank shaft in case it has a pilot bearing in it not allowing the converter to seat in the crank.
|
| Sun Jul 15, 2018 2:39 pm |
|
|
|
Backcountryrenegade
Official CCB Member
Joined: Fri May 15, 2015 10:28 pm
Posts: 41
Location: Elizabeth, CO
|
Re: 351 install So damn close... 
|
| Sun Jul 15, 2018 4:54 pm |
|
|
|
Viperwolf1
Official CCB Member
Joined: Tue May 07, 2013 10:37 pm
Posts: 1485
|
Re: 351 install Something not right there. Don't try to force it together with the bolts. You can break an expensive trans pump. Either converter is not all in or something else. What flexplate is it? C6 flexplate is different.
|
| Sun Jul 15, 2018 10:16 pm |
|
|
|
Backcountryrenegade
Official CCB Member
Joined: Fri May 15, 2015 10:28 pm
Posts: 41
Location: Elizabeth, CO
|
Re: 351 install It’s a 28oz flex plate. It was a bit hung up on the torque converter. I just need extra hands at this point, somebody who’s done this.
|
| Tue Jul 17, 2018 1:53 pm |
|
|
|
|
|
Page 1 of 1
|
[ 8 posts ] |
|
Who is online |
Users browsing this forum: No registered users and 20 guests |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum
|
|
