|
It is currently Mon Nov 25, 2024 4:49 pm |
|
All times are UTC - 7 hours [ DST ] |
|
Page 1 of 1 |
[ 10 posts ] |
| Previous topic | Next topic |
intake torque setting's
| Author | Message |
|---|---|
|
Official CCB Member  Joined: Wed Dec 08, 2010 3:49 pm Posts: 128 Images: 0 
|
 intake torque setting'sDoes anybody know what i should torque my new intake manifold to? and in what order? it's an edlebrok performer if that helps i'm also looking to getting new bolt's for the intake. any info would help thank's!!
matt.  _________________ 71 bronco 5.5 lift 35's dana 44, 9 inch locked in the rear 4 wheel disc brakes np435 and finaly power steering!!! |
| Sun Mar 13, 2011 3:41 pm |
|
|
|
|
|
Re: intake torque setting's It's all on the last page of the instructions: http://www.edelbrock.com/automotive_new ... 0/2121.pdf
|
| Sun Mar 13, 2011 3:50 pm |
|
|
|
|
Official CCB Member Joined: Wed Dec 08, 2010 3:49 pm Posts: 128 Images: 0
|
Re: intake torque setting's thank's viperwolf any ideas on the bolts?
_________________ 71 bronco 5.5 lift 35's dana 44, 9 inch locked in the rear 4 wheel disc brakes np435 and finaly power steering!!! |
| Sun Mar 13, 2011 3:57 pm |
|
|
|
|
Official CCB Member  Joined: Sun Jan 02, 2011 9:37 pm Posts: 320
|
Re: intake torque setting's ...dont use crappy ones. ask me how i know
|
| Mon Mar 14, 2011 3:05 pm |
|
|
|
|
|
Re: intake torque setting's I used studs for the intake. Ace has them.
|
| Mon Mar 14, 2011 5:53 pm |
|
|
|
|
Official CCB Member Joined: Wed Dec 08, 2010 3:49 pm Posts: 128 Images: 0
|
Re: intake torque setting's Oooh what happened with the crappy one's i'm always intersted in a good story!!
 _________________ 71 bronco 5.5 lift 35's dana 44, 9 inch locked in the rear 4 wheel disc brakes np435 and finaly power steering!!! |
| Mon Mar 14, 2011 7:48 pm |
|
|
|
|
Official CCB Member  Joined: Sat Dec 11, 2010 8:33 pm Posts: 54 Images: 1 Location: Parker, CO
|
Re: intake torque setting's mat there is a chilton manual in top draw in garage by da refrig you r welcome to go get it . i think they are 5/16 and 20 to 25 ft lbs .if i remember right . use some sealer around matting surface
cheers . Molley _________________ 66 Bronco (Molley) injected 418 stroker on juice, klune v ,4 speed atlas hi 9 35 spline air lockers front & rear, rcv axles. 37'' red krawlers. Four other sets of tires for ice racing and dirt drags. 290lbs of welding wire. |
| Mon Mar 14, 2011 8:01 pm |
|
|
|
|
Official CCB Member Joined: Sat Dec 11, 2010 8:33 pm Posts: 54 Images: 1 Location: Parker, CO
|
Re: intake torque setting's start toward middle and chris cross for pattern
again cheers Molley _________________ 66 Bronco (Molley) injected 418 stroker on juice, klune v ,4 speed atlas hi 9 35 spline air lockers front & rear, rcv axles. 37'' red krawlers. Four other sets of tires for ice racing and dirt drags. 290lbs of welding wire. |
| Mon Mar 14, 2011 8:02 pm |
|
|
|
|
Official CCB Member  Joined: Fri Oct 01, 2010 8:45 am Posts: 521 Images: 0 Location: Colorado Springs
|
Re: intake torque setting's |
| Tue Mar 15, 2011 10:45 am |
|
|
|
|
Official CCB Member Joined: Wed Dec 08, 2010 3:49 pm Posts: 128 Images: 0
|
Re: intake torque setting's Sweet thanks for the info guy's. the intake is going back on tonight!! hopefully will have the motor running by the weekend!
_________________ 71 bronco 5.5 lift 35's dana 44, 9 inch locked in the rear 4 wheel disc brakes np435 and finaly power steering!!! |
| Wed Mar 16, 2011 7:32 pm |
|
|
|
|
|
Page 1 of 1 |
[ 10 posts ] |
|
All times are UTC - 7 hours [ DST ] |
Who is online |
Users browsing this forum: No registered users and 42 guests |
| You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum |