| www.ColoradoClassicBroncos.com http://coloradoclassicbroncos.com./ |
|
| Cut Sheet Metal http://coloradoclassicbroncos.com./viewtopic.php?f=4&t=796 |
Page 1 of 1 |
| Author: | Entourage [ Sat Jan 29, 2011 12:48 am ] |
| Post subject: | Cut Sheet Metal |
My rockers are rough on the bottom and really just need to weld in a new panel. I need 2 piece of sheet metal 4" x 40" - is there a place open on Saturday to get this kind of stuff? |
|
| Author: | Entourage [ Sat Jan 29, 2011 10:24 am ] |
| Post subject: | Re: Cut Sheet Metal |
Killa - that is right by my house too! Thanks Dan. |
|
| Author: | ZOSO [ Sat Jan 29, 2011 10:49 am ] |
| Post subject: | Re: Cut Sheet Metal |
just cut them off. you dont need rockers. all they do is collect dirt and mud. rust out and get smashed when wheelin. |
|
| Author: | Entourage [ Sat Jan 29, 2011 12:14 pm ] |
| Post subject: | Re: Cut Sheet Metal |
Cutting the rockers was totally the plan then got new uncut fenders and the whole build changed - crazy I know. A month ago I was fo sho going to cut it all off. |
|
| Author: | ZOSO [ Sat Jan 29, 2011 6:09 pm ] |
| Post subject: | Re: Cut Sheet Metal |
Still not too late. You havent painted it yet. |
|
| Author: | PonyCorral [ Sun Jan 30, 2011 9:34 am ] |
| Post subject: | Re: Cut Sheet Metal |
I saw some cool rocker covers check these out, they are from West Coast Broncos. http://www.wcb4x4.com/mm5/merchant.mvc? ... y_Code=EXT |
|
| Author: | Entourage [ Sun Jan 30, 2011 12:09 pm ] |
| Post subject: | Re: Cut Sheet Metal |
Those are Bad A, I think Dnewman has those on his Bronco. |
|
| Author: | PonyCorral [ Sun Jan 30, 2011 1:49 pm ] |
| Post subject: | Re: Cut Sheet Metal |
He does and they are bad a**! He said that this was the first bronco he had with good rockers and wanted to keep them that way. WCB uses rattle cans to paint them so that they are easy to touch up. |
|
| Author: | Justin [ Sun Jan 30, 2011 4:25 pm ] |
| Post subject: | Re: Cut Sheet Metal |
You know they're no joke when your rockers weigh 63 lbs. I'm torn between cutting my rockers (rust) and doing something like this. I'd cut them in a heartbeat, but kind of want to maintain use of my aux tank. |
|
| Author: | ZOSO [ Sun Jan 30, 2011 4:49 pm ] |
| Post subject: | Re: Cut Sheet Metal |
| Author: | Justin [ Sun Jan 30, 2011 5:46 pm ] |
| Post subject: | Re: Cut Sheet Metal |
I've been thinking about something like that. Maybe doing a regular 2x6 slider on the passenger's side and building either a 2x6 with an additional plate to cover the tank or a triangular slider w/more space for compressed air. |
|
| Author: | PonyCorral [ Sun Jan 30, 2011 10:46 pm ] |
| Post subject: | Re: Cut Sheet Metal |
Come on by, I just put a new one on the DS...It makes a helluva difference in the look! Since your gonna run uncut I think you will like them with or with out the covers. |
|
| Author: | Entourage [ Sun Jan 30, 2011 11:37 pm ] |
| Post subject: | Re: Cut Sheet Metal |
There has been chats off and on over the last few months about rockers and I know that CMCDowell wanted to build some from the 2 x 6 square tubing as well. That would be an awesome tech class. I remember Dan chimed in stating he wanted to use his for air tanks. |
|
| Author: | Entourage [ Fri Feb 04, 2011 1:18 pm ] |
| Post subject: | Re: Cut Sheet Metal |
I called Commercial Sheet Metal in Denver - they are cutting me 2 new rockers 4" x 40" for $5.00 Each and ready this afternoon. I hope they will do a great job and become another resource for the club. |
|
| Page 1 of 1 | All times are UTC - 7 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|