| www.ColoradoClassicBroncos.com http://coloradoclassicbroncos.com./ |
|
| Wheel studs http://coloradoclassicbroncos.com./viewtopic.php?f=4&t=6783 |
Page 1 of 1 |
| Author: | Justin [ Thu Sep 11, 2014 2:40 pm ] |
| Post subject: | Wheel studs |
I'm switching to alloy wheels from steel and they're thicker. I'm assuming I need longer wheel studs. How much stud needs to be engaged to be safe? Just need to figure out how long a stud I need to buy. |
|
| Author: | Gregg [ Thu Sep 11, 2014 3:05 pm ] |
| Post subject: | Re: Wheel studs |
you're killing me. |
|
| Author: | Dukietown [ Thu Sep 11, 2014 4:28 pm ] |
| Post subject: | Re: Wheel studs |
If you know what I mean... |
|
| Author: | Justin [ Thu Sep 11, 2014 4:29 pm ] |
| Post subject: | Re: Wheel studs |
I was wondering how fast this would go there. :-) |
|
| Author: | landshark [ Thu Sep 11, 2014 4:45 pm ] |
| Post subject: | Re: Wheel studs |
Enough to get your nuts tight without bottoming out. There |
|
| Author: | Justin [ Thu Sep 11, 2014 4:58 pm ] |
| Post subject: | Re: Wheel studs |
So if I run open ended nuts I can use really long studs? |
|
| Author: | landshark [ Thu Sep 11, 2014 9:36 pm ] |
| Post subject: | Re: Wheel studs |
| Author: | B.O.B. [ Fri Sep 12, 2014 6:39 am ] |
| Post subject: | Re: Wheel studs |
Since most of us use 1/2 inch lug nuts you need about the same for engagement to be safe. Usually if you get at least 8 full turns you are good. Open end or closed won't really matter. Usually the stock studs will be sufficient. |
|
| Author: | Jesus_man [ Fri Sep 12, 2014 8:10 am ] |
| Post subject: | Re: Wheel studs |
But in a serious note, you don't want them so long that you can catch rocks on them. I would go with a length that protrudes 5/8" beyond the wheel. Are the new wheels lug-centric? I hope so. Flat lugs needed checked almost daily on alloy's! I ruined a set in high school. For that matter, I have also damaged my lug-centric beadlocks as well... |
|
| Author: | Justin [ Fri Sep 12, 2014 11:13 am ] |
| Post subject: | Re: Wheel studs |
The new wheels are lug-centric. Just remembered a second question on the same topic. With my current lug nuts I can't get a socket into the very narrow area that the lugs reside in. Is the usual solution smaller lug nuts or a thin walled socket? Cue Gregg.... |
|
| Author: | Gregg [ Fri Sep 12, 2014 11:24 am ] |
| Post subject: | Re: Wheel studs |
Still not taking the bait....but you guys are making me laugh. ---Gx3 |
|
| Author: | akaFrankCastle [ Fri Sep 12, 2014 11:49 am ] |
| Post subject: | Re: Wheel studs |
Thin wall sockets. |
|
| Author: | Justin [ Fri Sep 12, 2014 12:40 pm ] |
| Post subject: | Re: Wheel studs |
Cool, thanks. |
|
| Author: | Colorado75bronc [ Fri Sep 12, 2014 10:49 pm ] |
| Post subject: | Re: Wheel studs |
Thin wall socket or worst case the crappy spline drive lug nuts Sent from my iPhone using Tapatalk |
|
| Page 1 of 1 | All times are UTC - 7 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|